Scope of accreditation · Inspection
Design compliance inspection
Identify non-conformities before construction begins.
We assess the conformity of the design or part of it with the applicable normative and technical documents before construction begins. The result is recorded in a report describing the defects identified.
- Accreditation certificate
- GAC-IB-0299
- Body type
- Type A
- Standard
- ISO/IEC 17020:2012/2013
- Valid
- until 10.07.2028
01 · Subject of inspection
What we inspect
We determine the facility’s of the design documentation and the design sections conformity with the technical specification and/or against the established requirements — structural and architectural sections, engineering-geological and hydrological surveys, engineering networks.
| Area | Subject of inspection |
|---|---|
| Engineering-geological section | Conformity of the survey and the conclusion with the applicable requirements |
| Structural section | Conformity of structural solutions with the normative and technical documents |
| Architectural section | Conformity of the architectural section with the established requirements |
| Power and low-current systems | Power supply and low-current systems and their technological part |
| Water supply and drainage | Water supply, sewerage and drainage systems |
| Heating and ventilation | Ventilation, air-conditioning and heating systems |
02 · Result
What you receive
Inspection report
- the subject of inspection and the scope of services;
- the basis of assessment — which design, norms and requirements were applied;
- methods applied and inspection dates;
- Conformity assessment result — where this is provided for within the scope of services;
- non-conformities identified, with descriptions and evidence;
- limitations of the assessment — what was not inspected and for what reason;
- Certification by an authorised person.
03 · Process
How an inspection is carried out
01
Defining the criteria
We define the assessment criteria on the basis of the applicable requirements and agree the scope of services.
02
Documentary review
Review of the documentation submitted and comparison against the applicable requirements.
03
Technical review
Verification of the mutual consistency of the design sections and of their conformity with the norms.
04
Reporting
Documenting the findings, non-conformities and limitations, and delivering the report.
04 · Scope and legal basis
What you should know
Why mandatory expert examination is not enough
Scope of services
- The inspection result is based on the scope of assessment, the methods applied and the evidence collected.
- The company does not perform the works it independently inspects, nor does it take part in the design of the facility.
- Mandatory requirements are neither altered nor reduced by agreeing the scope of services.
- An inspection does not imply a predetermined favourable conclusion and provides no guarantee of an administrative decision.
05 · Related
Other services
The accreditation status of each service is defined by the annex to the scope of accreditation.
Normative documents and procedures TA-IP-05-19 · 07-17 · 08-18 · 09-18 · 10-18 · 11-18 · 12-18 · 13-18 · 14-18 · 21-22 · 22-22
- Construction norms and rules — SNiP, Parts 1–4
- Technical regulations governing the construction sector in the territory of Georgia — №71 (2014)
- Technical regulation “On approval of national accessibility standards” — №732 (2020)
- Technical regulation — №41 (2016)
- National standard of Georgia SST 72:2009 — motor roads for public use: geometric and structural requirements
- Guide to the survey and design of railway and road bridge crossings over watercourses — НИМП-72
- Rules for the installation of electrical equipment — ПУЭ
- Technical regulation on the rules for the operation of power plants and networks — №434 (2013)
- Technical regulation on safety rules for the operation of electrical installations — №340 (2013)
- Rules for the protection of linear structures of electrical networks — №366 (2013)
- Departmental construction norms — ВСН
- ISO/IEC 11801-2017 — information technology, generic cabling, Part 6
- TA-IP-05-19, 07-17, 08-18, 09-18, 10-18, 11-18, 12-18, 13-18, 14-18, 21-22, 22-22 — inspection methods and procedures
Source — scope of accreditation, certificate GAC-IB-0299 (updated 10.06.2026). View the scope (PDF) ↗
06 · Contact
Contact us
For the inspection of your facility — quality begins with the right decision.
Save time — submit your application online.
- Address
- Tbilisi, 14a Alexander
Kazbegi Avenue, 3rd floor - Phone
- +995 599 81 87 87
- [email protected]
- Legal name
- TIAG Auditescort LLC
- Identification code
- 205229439
- Accreditation certificate
- GAC-IB-0299